रसायन विज्ञान से आप क्या समझते हैं ? इसकी शाखाएँ कौन-कौन सी हैं?

रसायन विज्ञान से आप क्या समझते हैं ?

प्रश्न – रसायन विज्ञान से आप क्या समझते हैं ? इसकी शाखाएँ कौन-कौन सी हैं?
अथवा
रसायन विज्ञान का वर्गीकरण कीजिए।

उत्तर : रसायन विज्ञान-विज्ञान की वह शाखा जिसके अन्तर्गत पदार्थों की संरचना, संघटन, गुण-धर्म तथा उनमें होने वाले विभिन्न परिवर्तनों का अध्ययन किया जाता है, रसायन विज्ञान’ कहलाती है। रसायन विज्ञान की शाखाएँ-अध्ययन की सुविधा के आधार पर रसायन विज्ञान को निम्नलिखित शाखाओं में वर्गीकृत किया गया है

(A) शुद्ध रसायन (Pure chemistry)

(B) व्यावहारिक अथवा अनुप्रयुक्त रसायन (Applied chemistry)

(A) शुद्ध रसायन : – शुद्ध रसायन को निम्नलिखित उपशाखाओं में विभाजित किया गया है

  1. अकार्बनिक रसायन —इसके अन्तर्गत सभी तत्वों (कार्बन को छोड़कर) और उनके यौगिकों के बनाने की विधि,गुण-धर्म,उपयोग तथा संघटन आदि का अध्ययन किया जाता है
  2. कार्बनिक रसायन–इसके अन्तर्गत कार्बन के यौगिकों का विस्तृत अध्ययन किया जाता है ।
  3. भौतिक रसायन-इसके अन्तर्गत रासायनिक अभिक्रियाओं के नियमों तथा सिद्धान्तों का अध्ययन किया जाता है।
  4. जैव रसायन-इसके अन्तर्गत जीवधारियों में होने वाली रासायनिक अभिक्रियाओं तथा जन्तुओं एवं वनस्पतियों से प्राप्त पदार्थों का अध्ययन किया जाता है ।
  5. वैश्लेषिक रसायन इसके अन्तर्गत पदार्थों के गुणों के आधार पर उनकी पहचान तथा मात्रा निर्धारित करने की विधियों का अध्ययन किया जाता है।

(B) व्यावहारिक रसायन : – व्यावहारिक रसायन विज्ञान को निम्नलिखित उपशाखाओं में विभाजित किया जा सकता है

  1. औद्योगिक रसायन-इसके अन्तर्गत जीवनोपयोगी पदार्थों; जैसे—कपड़ा, सीमेण्ट, प्लास्टिक, काँच, साबुन, वार्निश,पेन्ट,चीनी आदि के औद्योगिक निर्माण की विधियों एवं नियमों का अध्ययन किया जाता है
  2. कृषि रसायन इसके अन्तर्गत कृषि तथा उसके उपयोगी पदार्थों जैसे- उर्वरक, खनिज लवणों आदि का अध्ययन किया जाता है
  3. मृदा रसायन-इसके अन्तर्गत भूमि की रासायनिक प्रकृति का अध्ययन किया जाता है।
  4. खनिज रसायन-इसके अन्तर्गत खनिजों की रासायनिक प्रकृति (संघटन आदि) का अध्ययन किया जाता है
  5. खाद्य रसायन-इसके अन्तर्गत खाद्य पदार्थों का संघटन तथा उनमें मिलावट आदि का अध्ययन किया जाता है।
  6. युद्ध रसायन-इसके अन्तर्गत युद्ध में काम आने वाली सामग्री आदि का अध्ययन करते हैं।
  7. अपराध रसायन-इसके अन्तर्गत रक्त, पसीना, कपड़े आदि का रासायनिक अध्ययन करके वास्तविक अपराधी को पकड़ा जाता है।
  8. औषधि रसायन-इसके अन्तर्गत रोगों के उपचार में प्रयुक्त होने वाले रासायनिक द्रव्यों का अध्ययन किया जाता है।
  9. अन्तरिक्ष रसायन-इसके अन्तर्गत वायुयानों में काम आने वाले ईंधनों, उनके बनाने में काम आने वाली सामग्री तथा अन्तरिक्ष यात्रियों के वस्त्रों के बनाने में काम आने वाली सामग्री आदि का अध्ययन किया जाता है।
  10. नाभिकीय रसायन-इसके अन्तर्गत परमाणु के नाभिक में होने वाले परिवर्तनों का अध्ययन किया जाता है नाभिकीय विखण्डन तथा नाभिकीय संलयन इसके उदाहरण हैं।

रसायन विज्ञान से आप क्या समझते हैं ?

ये भी पढ़े….

ITI workshop calculation and science mcq 2022 | बहुविकल्पीय प्रश्न

हुविकल्पीय प्रश्न

1- इस्पात बनाने की सबसे उत्तम विधि हैं।
(a) विद्युत आर्क भट्ठी
(b) ओपन हार्थ विधि
(c) बेसेमर विधि
(d) क्रुसीबल विधि

2- पिटवाँ लोहे का उत्पादन में किया जाता है
(a) क्यूपोला
(b) धमन भट्ठी
(c) पुडलिंग भट्ठी
(d) इनमें से कोई नहीं

3- लैड सल्फाइड मुख्य अयस्क हैं।
(a) सीसे का
(b) टिन का
(c) चाँदी की
(d) पीतल का

4- मैग्नेटाइट का सूत्र है
(a) Fe2O3
(b) Fe2O3 .3H3O
(c) Fe3O4
(d) FeCO3

5- आयरन के निष्कर्षण में निम्न में से क्या धातु मल बनता है t
(a) FeSiO3
(b) CaSiO3
(c) Ca3 (PO4)2
(d) FePO4

iti workshop calculation and science mcq pdf in hindi

6- आयरन का सबसे शुद्ध प्रारूप कौन-सा है?
(a) कच्चा लोहा
(b) ढलवाँ लोहा
(c) पिटवाँ लोहा
(d) इस्पात

7- इस्पात में कार्बन की क्या प्रतिशतता होती है?
(a) 0.1 से 0.25%
(b) 0.25 से 1.5%
(c) 2 से 4%
(d) 0.0%

8- ढलवाँ लोहे का गलनांक होता है
(a) 1520°C
(b) 520°C
(c) 2000°C
(d) 1600°C

9- एल्युमीनियम का आपेक्षिक घनत्व है
(a) 2.7°C
(b) 3.7°C
(c) 2.9°C
(d) 4.0°C

10- निम्न में से कौन लौह-अयस्क (iron ore) नहीं है?
(a) हेमेटाइट
(b) मैग्नेटाइट
(c) लिमोनाइट
(d) एंगिल आयरन

11- अलौह धातुएँ निम्न में से होगी
(a) एल्युमीनियम
(b) क्रोमियम
(c) जस्ता
(d) ये सभी

12- सीसे की प्राप्ति का मुख्य अयस्क है
(a) लैड-काबोंनेट
(b) लैड-सल्फेट
(c) लैड-सल्फाइड
(d) ये सभी

13 – निकिल-ताँबा एलॉय की मुख्य मिश्र धातु ‘मोनल मैटल’ में कार्बन की मात्रा होती है
(a) 1.50%
(b) 0.25%
(c) 28.00%
(d) 68.00%

14 – आघातवर्द्धयता सबसे अधिक होती है
(a) सोने में
(b) चाँदी में
(d) पीतल में
(c) लोहे में

15 – पाइराइट्स का रासायनिक सूत्र है
(a) FeS2
(b) FeSO4
(c) Fe2O7
(d) Fe2O4

16 – निम्न में से किस मुख्य अयस्क में जस्ता अधिक मात्रा में पाया जाता है?
(a) जिंक ब्लैड
(b) कैलेमीन
(c) फ्रेंकिनाइट
(d) जिंकाइट

17 – वात्या भट्ठी में अधिकतम तापमान होता है
(a) अपचयन खण्ड
(b) धातुमय खण्ड
(c) दहन खण्ड
(d) गलन खण्ड

18 – हेमेटाइट से आयरन का निष्कर्षण करने में चूना पत्थर का उपयोग होता है
(a) अपचायक के रूप में
(b) स्लैम के रूप में
(c) पवस्क के रूप में
(d) गैस के रूप में

19 – कास्ट आयरन के लिए प्रयुक्त कूलैन्ट है
(a) घुलनशील तेल
(b) पानी
(c) डाई
(d) इनमेंसे कोई नहीं

20 – मृदु स्टील में कार्बन की प्रतिशतता है
(a) 0.2%
(b) 0.8%
(c) 1.8%
(d) इनमेंसे कोई नहीं

21 – काँसा बनाने के लिए ताँबे के साथ कौन-सी धातु मिलायी जाती है?
(a) टिन
(b) लोहा
(c) जिंक
(d) मैंगनीज

22 – लोहे का शुद्धतम रूप है
(a) कास्ट आयरन
(b) रॉट आयरन
(c) स्टील
(d) पिग आयरन

23 – गेलेना का अयस्क है।
(a) टिन
(b) लैड
(c) क्रोमियम
(d) ताँबा

Answer : 1-a, 2-c, 3-a, 4- c, 5- d ,6- c , 7-b, 8-a, 9-a, 10-d, 11-d, 12-c, 13-b, 14-a,15-a, 16-d, 17-c , 18-c , 19-d , 20-a, 21-a, 22-b, 23-b

(iti workshop calculation and science mcq  ,iti workshop calculation and science question paper pdf 2020,workshop calculation and science mcq pdf 1st year,iti workshop calculation and science mcq online test,bharat skill workshop calculation and science mcq pdf,iti workshop calculation and science 1st year,iti workshop calculation and science mcq pdf in hindi,workshop calculation and science iti syllabus 2020,ITI 1st Year Workshop Calculation & Science MCQ Bharat Skill 2021,bharat skill pdf)

 

ये भी पढ़े

ITI Diesel 1st Year Objective Question Answer in hindi

बहुविकल्पीय प्रश्न (MCQs)

1- डीजल इंजन में ईंधन संभरण पम्प लगा होता है

 (a) ईंधन टंकी पर

 (b) इंजेक्शन पम्प पर 

 (c) इंजेक्टर पर 

(d) ईंधन टंकी के भीतर

Answer – b

2- डीजल ईंधन में द्वितीयक फिल्टर होता है 

(a) अनिवार्य

 (b) ईंधन टंकी तथा संभरण पम्प के बीच लगा हुआ

(c) ऐच्छिक

(d) ईंधन से पानी निकालने में असमर्थ

Answer -a

3- ऑटोमोटिव डीजल इंजन में संपीडन अनुपात प्रायः होती है

(a) 7 : 1

 (b) 10 : 1 

(c) 15 : 1

 (d) 22:1

Answer -d

4- डीजल इंजन में फ्रैंकिंग संपीडन दाब होती है लगभग 

 (a) 1000 kPa 

(b) 2000 kPa 

(c) 3000 kPa

 (d) 10,000 kPa

Answer -c

5 – वितरक प्रकार के पम्प में ईंधन इंजेक्शन टाइमिंग नियंत्रित होती है

(a) प्लंजर की स्ट्रोक बदलने से 

(b) रोटर की गति बदलने से

(c) कैम वलय को घुमाने से

(d) वलय पर कैमों की संख्या बदलने से

 Answer -c

6- ऐनेराइड होता है

(a) शीत अवस्था से स्टार्ट करने का उपकरण

 (b) उत्सर्जन-नियंत्रण उपकरण  

 (c) विसंपीडन उपकरण

(d) इंजेक्शन-टाइमिंग उपकरण

Answer -b

7- ग्लो-प्लग होता है

(a) विसंपीडन उपकरण

(b) प्रवेश मैनीफोल्ड पर लगा हुआ

(c) दहन कक्ष में कसा हुआ 

(d) ईंधन की लीकेज बंद करने के लिए

Answer -c

8- डीजल इंजन में अत्यधिक धुआँ निकलना सामान्य होता है

(a) स्टार्टिंग के समय

 (b) त्वरण के समय

 (c) अवत्वरण के समय

 (d) अलसन के समय

Answer -b

9- डीजल इंजन के सिलेण्डरों में संपीडन के बाद का तापमान होता है लगभग

(a) 300°C

 (b) 450°C

 (c) 800°C

 (d) 1000°C

Answer -b

10- कुछ डीजल इंजनों में इंजेक्शन दाब हो सकता है 

(a) 100 MPa

 (b) 200 MPa

 (c) 300 MPa 

(d) 400 MPa

Answer -b

11- छिद्र प्रकार के नॉजलों में खुलने का दाब होता है

(a) 5 से 10 MPa के बीच 

(b) 10 से 20 MPa के बीच 

(c) 17 से 34 MPa के बीच 

(d) 27 से 54 MPa के बीच

  Answer -c

12- डीजल ईंधन का प्रज्वलन तापमान होता है लगभग

  (a) 300°C

 (b) 400°C 

(c) 600°C

 (d) 800°C

Answer -b

13- पिंटल प्रकार के नॉजल में खुलने का दाब होता है

(a) 7 से 15 MPa के बीच 

(b) 11 से 22 MPa के बीच 

(c) 17 से 34 MPa के बीच

 (d) 27 से 54 MPa के बीच

Answer -a

14- हीटर प्लग कहाँ फिट किए जाते हैं? 

(a) गवर्नर में

(b) कम्बशन चैम्बर में

(c) फ्यूल इंजेक्शन पम्प में

(d) स्पिण्डल के साथ

Answer -b

15- डीजल की अनियमित सप्लाई का कारण हो सकता है 

(a) एयर लॉक

(b) गन्दा फिल्टर

 (c) टैपिट रोल घिसा होना ।

 (d) उपर्युक्त सभी

Answer -d

16- अधिक होने का कारण हो सकता है

 (a) नॉजल वाल्व जमा होना

(b) स्प्रिंग टूटी होना

 (c) एयर लॉक

(d)नॉजल वाल्व कटा होना 

 Answer -a

17- किस प्रकार के कम्बशन चैम्बर में कॉनकेव हैड पिस्टन का प्रयोग होता है?

(a) सॉलिड इंजेक्शन 

(b) मैकेनिकल 

(c) स्विरल चैम्बर

 (d) सेन्टर स्फीयर

Answer -a

18- किस प्रकार के गवर्नर में डायग्राम प्रयोग होता है

 (a) हाइड्रॉलिक 

(b) मैकेनिकल

 (c) न्यूमैटिक 

(d) इनमें से कोई नहीं

Answer -c

19- न्यूमैटिक गवर्नर के साथ इनलेट मैनीफोल्ड में लगी होती है

(a) नाजल

 (b) प्लंजर

(c) बटर फ्लाई

(d) स्प्रिग

Answer -c

20- डीजल इंजनों के फ्यूल इंजेक्शन पम्प की सेटिंग जो डीजल इंजेक्शन की समान मात्रा के लिए की जाती है, क्या कहलाती है?

(a) फेजिंग

(b) कैलीब्रेशन

(c) (a) तथा (b) दोनों

(d) इनमें से कोई नहीं 

 Answer -b

21- डिलीवरी वाल्व खुलता है

(a) स्प्रिंग द्वारा 

(b) डीजल के दबाव से 

(c) कण्ट्रोल रॉड द्वारा 

(d) इनमें से कोई नहीं

 Answer -b

22- इंजेक्टर का कार्य है

(a) डीजल सप्लाई को रोकना

(b) डीजल स्प्रे करना

(c) डिलीवरी वाल्व को खोलना

(d) उपर्युक्त में से कोई नहीं

Answer -d

23- इंजेक्टर में कौन-कौन से टेस्ट किए जाते हैं? 

(a) इंजेक्टर प्रेशर टेस्ट 

(b) इंजेक्टर स्प्रे टेस्ट

 (c) (a) तथा (b) दोनों 

(d) इनमें से कोई नहीं

Answer -c

24- किस प्रकार के गवर्नर में सेन्ट्रीफ्यूगल वेट का प्रयोग होता है?

 (a) मैकेनिकल

 (b) न्यूमैटिक

 (c) हाइड्रॉलिक

 (d) (a) तथा (b) दोनों

Answer – a

25- डीजल इंजन में अधिकतम व न्यूनतम चाल नियमित रखने के लिए फ्यूल इंजेक्शन पम्प के साथ क्या प्रयोग किया जाता है?

 (a) गवर्नर

(b) नॉजल

(c) प्लंजर

 (d) वाल्व

Answer -a

ITI Diesel 1st Year Objective Question Answer in hindi

ये भी पढ़े

Electrician 1st year MCQ Question Answer in English 2021

Electrician 1st year MCQ Question Answer in English 2021

हेलो दोस्तों,

में जानता हूँ की आप सभी को Electrician MCQ या बहुविकल्पि प्रशन की आवश्यकता होती है। इसलिए मै आप सभी के लिए NIMI पैटर्न पर आधारित Electrician 1st Year’s  MCQ Question  Answer ‘s in English 2021 दिए गए हैं। ये Question’s आईटीआई के Exam में 100% पूछे जाते हैं।
अगर आप सभी को ITI Electrician 1st Year’s MCQ का PDF file Download भी कर सकते हैं।
Download करने के लिए आप इस Link :- ( www.itiquestionbank.com ) से आप किसी भी Trade का ईयर वाईस  PDF Download क्र सकते है। ( iti electrician 1st year mcq nimi, iti bharatskill nimi, iti Electrician 1st year pdf download, iti Electrician 1st year nimi  pdf download, iti electrician 1st year objective question and answer, iti electrician 1st year objective  pdf file download )

# Objective types Question and Answer’s :- 

1.What is the use of this gauge?
(a) Defective storage
(b) Check the internal radius of the job
(c) Check the height and parallism of job
(d) Set the job on machines parallel to datum

2.What is the name of the file?
(a) Rasp cut file
(b) Single cut file
(c) Double cut file
(d) Curved cut file

3.What is the name of the tool?
(a) Divider
(b) Inside caliper
(c) Odd leg caliper
(d) Outside caliper

4.What is the cause for twisting defect in timber?
(a) Defective storage
(b)Uneven shrinkage
(c) Improper seasoning
(d) Irregularity in growth of branches

5.What is the use of mortise chisel?
(a) General chiselling work in wood
(b) Making rectangular holes in wood
(c) Paring and finishing joints in wood
(d) Light chiselling cleaning sharp corners and in wood

6.Which type of stake is used for sharp bends in sheet metal?
(a) Square stake
(b) Hatchet stake
(c) Blow horn stake
(d) Bevel edge square stake

7.Which type of cold chisel is used for squaring materials at the corners?
(a) Web chisel
(b) Cross cut chisel
(c) Half round chisel
(d) Diamond point chisel

8.Which type of caliper is used to draw parallel lines along the outer edges of the materials?
(a) Inside caliper
(b) Jenny caliper
(c) Outside caliper
(d) Spring joint caliper

9.What is the name of the drill bit?
(a) Flat drill bit
(b) Taper shank bit
(c) Countersink bit
(d) Straight shank bit

10.What is the name of the stake used for general purpose in sheet metal work?
(a) Square stake
(b) Hatchet stake
(c) Blow horn square stake
(d) Bevel edge square stake

11.What is the number 1.25 indicates in ISO metric fine thread M12 x 1.25?
(a) Diametric of the thread
(b) Pitch of the thread
(c) Depth of the thread
(d) Length of the thread

12.What defect will occur in timber due to irregularity in growth of the branches?
(a) Knot
(b) Cupping
(c) Cracking
(d) Twisting

13.Which file is used for sharpening the blunt teeth of a tenon saw?
(a) Square file
(b) Round file
(c) Triangular file
(d)Half round file

14.Name the part marked ‘X’ of the file.
(a) Edge
(b) Heel
(c) Tang
(d) Shoulder

15.What is the name of the tool?
(a) Jenny caliper
(b) Inside caliper
(c) Outside caliper
(d) Firm joint caliper

16.What is the name of the angle marked ‘X’ of the chisel?
(a) Rake angle
(b) Point angle
(c) Clearance angle
(d) Inclination angle

[table id=2 /]

17.What is the use of firmer chisel?
(a) Paring and finishing joints
(b) General chiselling work
(c) Making rectangular holes in wood
(d) Light chiselling and to clean sharp corner

18.Which type of half lap joint is used if one part of a job meets another part at some distance from the ends?
(a) End-lap input
(b) Cross-lap joint
(c) Middle-lap joint
(d) Corner-half lap joint

19.Which type of notch is used for making a metal tray with 90° bend and an inside flange?
(a) ‘V’ notch
(b) Slant notch
(c) Square
(d) Straight notch

20.What is the purpose of hem folding in sheet metal work?
(a) Helps for forming a square box
(b) Helps for bending sheet metal easily
(c) Prevents burrs forming after cutting
(d) Prevents the sheet from damage

21.Which defect in the timber is caused to reduce its strength?
(a) Twisting
(b) Cupping
(c) Cracking
(d) Irregularity

22.What is the name of the hammer?
(a) Claw hammer
(b) Ball peen hammer
(c) Cross peen hammer
(d) Straight peen hammer

23.Which defect in timber is caused due to improper seasoning ?
(a) Knot
(c) Twisting
(d) Cracking
(d) Cupping

24.What is the name of the formation of thread marked as X in the galvanized sheet pipe joint?
(a) Hemp
(b) Full form thread
(c) Tapered male thread
(d) Parallel female thread

25.Which type of notch is used for bending the edge of the sheet?
(a) ‘V’ notch
(b) Slant notch
(c) Square notch
(d) Straight notch

26.What is the purpose of cross cut cold chisel?
(a) Cutting keyways
(b) Cutting curved grooves
(c) Squaring materials at corners
(d) Removing metal from large flat surface

27.Which type of notch is used to make a job with 90° bend?
(a) ‘V’ notch
(b) Slant notch
(c) Square notch
(d) Straight notch

28.Which type of curve cutting hand saw is used for internal cutting in wood?
(a) Compass saw
(b) Key hole saw
(c) Coping saw
(d) Fret saw

29.What is the name of the stake used for sheet metal work?
(a) Square stake
(b) Hatchet stake
(c) Blow-horn stake
(d) Bevel-edge square stake

30.What is the name of tool?
(a) Claw hammer
(b) Tack hammer
(c) Cross pein hammer
(d) Straight pein hammer

31.Which type of chisel is used for separating metals after chain drilling ?
(a) Flat chisel
(b) Web chisel
(c) Cross cut chisel
(d) Diamond point chisel

32.Which type of stake is used for riveting or seaming tapered cone shaped articles?
(a) Square stake
(b) Hatchet stake
(c) Blow horn stake
(d) Bevel edged square stake

33.Which causes knot defect in timbers?
(a) Defective storage
(b) Uneven shrinkage
(d) Growth of branches
(d) Improper seasoning

Read more

Welder mcq Question Answer 2021 paper

Welder mcq Question Answer 2021 paper

Welder mcq Question Answer 2021 paper

Welder mcq Question Answer 2021 paper

  1. बेस मेटल या पूरक धातु को एक साथ पिघलाने की क्रिया कहलाती है?
    • फ्यूजन
    • फोर्ज
    • सॉलिड
    • आर्क
    उत्तर. फ्यूजन
  2. विद्युत आर्क वेल्डिंग में प्रयोग होने वाला वेल्डिंग सेट कहलाता है?
    • डी.सी. जेनरेटर सेट
    • ए.सी. रेक्टीफायर सेट
    • डी.सी. रेक्टीफायर सेट
    • ये सभी
    उत्तर. ये सभी
  3. मीडियम कार्बन स्टील की वेल्डिंग के लिए जॉब को वैल्ड करनेसे पहले कितने तापमान तक प्री-हीट करना चाहिए?
    • 100-200°C
    • 150-250°C
    • 200-250°C
    • 300-400°C
    उत्तर. 150-250°C
  4. निम्नलिखित में कौनसा वेल्डिंग उपकरण है?
    • स्टील रूल
    • हथौड़ा
    • ट्राई स्क्वायर
    • ये सभी
    उत्तर. ये सभी
  5. एल्युमीनियम की वेल्डिंग के लिए निम्न विधि प्रयोग की जाता है?

• ऑक्सी-एसीटिलीन वेल्डिंग

• मेटल इनर्ट गैस वेल्डिं

• टंग्स्टन इनर्ट गैस वेल्डिं

• ये सभी

उत्तर. ये सभी

  1. वैल्डन धातुखण्डों को जोड़ने की निम्न में से कौनसी विधि है?
    • अस्थायी विधि
    • स्थायी विधि
    • अर्द्ध-स्थायी विधि
    • इनमें से कोई नहीं
    उत्तर. स्थायी विधि
  2. कटिंग ब्लो टॉर्च में किस गैस का प्रयोग किया जाता है?
    • शुद्ध ऑक्सीजन
    • शुद्ध हीलियम
    • शुद्ध हाइड्रोजन
    • शुद्ध नाइट्रोजन
    उत्तर. शुद्ध ऑक्सीजन
  3. किस विधि द्वारा फैरस तथा नॉन-फैरस धातुओं को आसानी से वैल्ड किया जाता है?
    • मेटल इनर्ट गैस वेल्डिंग
    • रेजिस्टेन्स वेल्डिंग
    • टंग्स्टन इनर्ट गैस वेल्डिंग
    • हाइड्रोजन आर्क वेल्डिंग
    उत्तर. मेटल इनर्ट गैस वेल्डिंग
  4. स्टेनलेस स्टील इलेट्रोड पर किसी कोटिंग नहीं होती है?
    • चूना
    • टिटेनियम
    • A व B दोनों
    • इनमें से कोई नहीं
    उत्तर. A व B दोनों
  5. इलेक्ट्रॉन बीम वेल्डिंग में जोड़ी जाने वाली सतहों के बीच दूरी मिमी है?
    • 0.050 – 0.075
    • 0.025 -0.050
    • 0.010-0.050
    • 0.075-0.090
    उत्तर. 0.050 – 0.075
  6. स्पॉट वेल्डिग निम्नलिखित में किस प्रकार की वेल्डिग हैं?
    • प्रेशर
    • वोल्यूम
    • फ्यूजन
    • आर्क
    उत्तर. प्रेशर
  7. बाल पीन हैमर का उपयोग होता है?
    • गोलाकार सतहों के लिए
    • चपटी सतहों के लिए
    • खोखली सतहों के लिए
    • ये सभी
    उत्तर. गोलाकार सतहों के लिए
  8. इलेक्ट्रोड लाइट कोटिंग में किस पदार्थ का मुख्य रूप से वाइंडरका कार्य होता है?
    • सोडियम सिलिकेट
    • पोटैशियम सिलिकेट
    • A व B दोनों
    • इनमें से कोई नहीं
    उत्तर. A व B दोनों
  9. स्टड को किसी प्लेट में जोड़ने के लिए प्रयुक्त वेल्डिग विधिका नाम है?
    • स्टड वेल्डिग
    • फ्रिक्शन वेल्डिंग
    • थर्मिट वेल्डिंग
    • आर्क वेल्डिंग
    उत्तर. स्टड वेल्डिग
  10. जिंक के लिए प्रयुक्त सोल्डर का गलनांक है?
    • 200°C
    • 202°C
    • 204°C
    • 205°C
    उत्तर. 202°C
  11. प्लेट की कटिंग करने से पहले प्री-हीटिंग तापमान लगभग कित°C रखा जाता है?
    • 100
    • 500
    • 700
    • 900
    उत्तर. 900
  12. MIG वेल्डिंग में प्रयुक्त इनर्ट गैस का नाम है?
    • CO2
    • NH
    • C,H
    • H
    उत्तर. CO2
  13. ए.सी. ट्रांसफॉर्मर निम्न प्रकार की सप्लाई के लिए बनाए जाते है?
    • सिंगल फेज
    • थ्री फेज
    • A व B दोनों
    • इनमें से कोई नहीं
    उत्तर. A व B दोनों
  14. प्लाज्मा आर्क वेल्डिंग की विधि का नाम है?
    • नॉन ट्रांसफर प्लाज्मा आर्क प्रोसेस
    • ट्रांसफर प्लाज्मा आर्क प्रोसेस
    • उपरोक्त दोनों
    • इनमें से कोई नहीं
    उत्तर. उपरोक्त दोनों

Welder mcq Question Answer 2021 paper

ये भी पढ़े

  1. ITI Welder MCQ question paper in hindi
  2. WSc 1st Years Question bank 2021
  3. वेल्डिंग के Top-20 महत्वपूर्ण प्रश्न उत्तर

ITI Electrician MCQ Question paper in English

ITI Electrician MCQ Question paper in English | ITI 1st year Electrician MCQ Question paper in English | ITI Electrician theory MCQ Question paper | ITI Electrician MCQ Question pdf

हेलो दोस्तों, में जानता हूँ की आप सभी को ITI Electrician 1st Year Question Solve paper 2021 या बहुविकल्पि प्रशन की आवश्यकता होती है। इसलिए मै आप सभी के लिए NIMI पैटर्न पर आधारित Electrician 1st Year’sand 2nd year’s का MCQ Question and Answer’s दिए गए हैं। ये Question’s आईटीआई के Exam में 100% पूछे जाते हैं। अगर आप सभी को ITI Electrician 1st Year’s and 2nd year’s MCQ का PDF file Download भी कर सकते हैं। ITI Electrician MCQ Question paper in English
Download करने के लिए आप इस Link 🙁 www.electrican.itiquestionbank.com ) से आप किसी भी Trade का ईयर वाईस pdf Download कर सकते है। ITI Electrician 1st Year Question Solve paper 2021

MCQ types Question: –

1- ……. Type insulators are often not used for voltages greater than.
(a)  66 Kw
(b)  33 Kw
(c)   25 kw
(d)   11 Kw
Answer – 33 Kw

2- Compared to amplifier, transformer cannot-
(a)  Increase of output power
(b)  Increase of output voltage
(c)  Increase of output stream
(d)  None of these
Answer: Increase of output power

3- If a coil, which establishes electrical contact with the constant, is said to be?
(a)  Short circuit
(b)  Open circuit
(c)    Closed
(d)    Earthed
Answer: Earthed

4- 3-phase induction motor should have three windings ……… installed at the electrical fraction.
(a)  90
(b) 120
(c)  360
(d)  60
Answer – 120

5- It is not possible to draw this diagram for complete wiring. But is it drawn to get consent by showing the customer?
(a)  Layout diagram
(b)  Installation Plan
(c)  Circuit diagram
(d)  Wiring diagram
Answer – Installation Plan

6- Electroplating occurs at which of the following?
(a)  Only at the cathode
(b)  Only at the anode
(c)  At both anode and cathode
(d)  At the anode or cathode
Answer – Only at the cathode

7- Bent snip is used?
(a)  To remove the beam.
(b)  To make the holes on the sheet
(c)  To fold the sheet.
(d)  For cutting the sheet along the wood lines
Answer – For cutting sheets along the wood lines

8- When a fluorescent lamp turns dark black at the ends. So it probably means that
(a)  Wrong gas has been filled in the lamp.
(b)  The lamp is switched on very rarely.
(c)   Starter is not working properly.
(d)   Deep is new.
Answer- The starter is not working properly.

9- What is called a natural magnet?
(a)   Steel
(b)   Load-stone
(c)    Magnetism
(d)    Soft iron
Answer: Load-stone

10- Stepper motors have applications …….
(a)   In coil winders
(b)   In fax machines
(c)    In lifts and hoists
(d)    In compressors
Answer – In fax machines

11- The length of the hacksaw blade is measured?
(a)    From the inner ends of two pin-holes.
(b)    Between the outer ends of two pin-holes.
(c)     Between the centers of two pin-holes
(d)     From the inner end of one pin hole and the outer end of another pin hole
Answer: Between the centers of two pin-holes

12- Which of the following materials is a conductor of electricity?
(a)    Rubber
(b)    Copper
(c)     Ebonite
(d)     Bakelite
Answer: Copper

13- The oscillating circuit that is made to convert the sine wave signal into a square wave signal is called-
(a)   Sammit Trigger
(b)   Blocking Oscillator
(c)    Multi – vibrator
(d)    Waynbridge oscillator
Answer – SammitTrigger

14- How can the cross-magnetizing effect of armature reaction in a DC generator be canceled?
(a)    Insert curved compensating
(b)    Providing poles of difference between the main pole
(c)    Transferring the position of the MNA brush from GNA
(d)    Ampere-turn increases in field windings.
Answer – By transferring the position of MNA brush from GNA

15- What is the rotational speed of a range motor in a weightless state?
(a)   Zero
(b)   3000 R.P.M.
(c)   3600 R.P.M.
(d)   Eternal
Answer: Eternal

16- In a nuclear reactor, the chain reaction is controlled by …….
(a)   Iron rods
(b)   Cadmium Rods
(c)    Graphite Rods
(d)    Brass rods
Answer: Cadmium Rods

17- I.C. What is the operating voltage of 555?
(a)   3 to 10 volts DC
(b)   1 to 5 volts DC
(c)    -5 to +5 volts DC
(d)   +5 to +15 volts D.C.
Answer – +5 to +15 volts D.C.

18- For measuring voltage across an impedance, VTVM is more reliable than a multimeter because
(a)   It has high sensitivity.
(b)   It presents high degeneration.
(c)    It does not change the measured voltage
(d)   All of the above
Answer – All of the above

19- Which substance is used to control chain reaction in a nuclear reactor?
(a)   Thorium
(b)   Heavy water
(c)    Boron
(d)    Beryllium
Answer: Boron

20- What is the yoke of a DC machine made of?
(a)   Copper
(b)   Carbon
(c)    Cast iron
(d)    Silicon Steel
Answer: Cast Iron

21- The rotation direction of DC motor can be changed –
(a)   By contrasting the supply combinations
(b)   Interchange the armature and field combinations
(c)    By adding a resistance in the field circuit
(d)   By contrasting armature or field combinations
Answer – By contrasting armature or field combinations

22- What is the electrochemical equivalent?
(a)   Ratio of atomic mass of hydrogen to atomic weight of an element
(b)   The free ratio of an element to the amount of hydrogen per unit
(c)    Ratio of atomic weight and valency
(d)    None of the above
Answer: The free ratio of an element to the amount of hydrogen per unit

23- This a. C. Isn’t the variety of winding?
(a)  Basket Winding
(b)  Concentric winding
(c)   Skein winding
(d)   Gram Winding
Answer – Gram Winding

24- What is the purpose of using damper in large-sized alternators?
(a)    Decrease current
(b)   Decreasing the voltage subtraction
(c)    Increase stability
(d)    Output B. raise up
Answer – Increase stability

25- In the category-B amplifier, the current flowing through it?
(a)   Less than uninterrupted semi-cycle.
(b)  For longer than uninterrupted semi-cycles
(c)   For uninterrupted half-cycle time
(d)   For uninterrupted full-cycle time
Answer – For uninterrupted half-cycle time

ये भी पढ़े….

  1. ITI Electrician 1st Year Question Solve paper 2021
  2. ITI Electrician 1st Year MCQ Question paper in hindi